PCBA Water-based cleaner T1008P Msds

Category：Water-based cleaner
The number of clicks：
Release date：2020-05-21
在線詢價

Detailed introduction

Part I Chemical products and company identification

chemical product

Product Name: TENICK T1006W

Recommended use: Used to clean all kinds of solder paste on SMT steel mesh.

Company logo

Brand	Supplier (Company Name / Address / Phone)	Company website
TENICK Singapore	Supplier name：SINGAPORE TENICK CLEANING TECHNOLOGY PTE.LTD. supplier address：50 Raffles Place,#34-04 Singapore Land Tower Singapore 048623 Supplier phone：(65)65326932	www.tenic.sg

Part II Hazard Overview

Classification: This product is not dangerous.

Hazard label

Health hazards: Excessive contact can cause eye, skin or respiratory irritation.

Environmental hazards: No obvious hazards.

Explosion hazard: Non-flammable liquid, no explosion hazard.

Part III Composition and composition information

Composition: Mixture.

Ingredient information:

NAME	CAS registration number	content
Amine nitrogen mixture	——	5%~10%
Methoxydipropylene glycol	34590-94-8	10~30%
Nitrogen containing carboxylic acid compound	29911-28-2	10~25%
Dipropylene glycol monoethyl ether	15764-24-6	5~10%
Cyclohexyl acetate	622-45-7	0.1~10%
Ethyl-3-methylbutyrate	108-64-5	0.1~10%

Part IV First Aid Measures

Inhalation

Use appropriate respiratory protection, if breathing irritation, dizziness, nausea, or confusion, seek medical attention immediately. Such as

If breathing stops, use mechanical equipment to help with ventilation, or perform mouth-to-mouth resuscitation first aid.

skin contact

Wash the area with soap and water. Take off contaminated clothing. Contaminated clothing should be washed before wearing.

eye contact

Rinse thoroughly with water. Seek medical assistance if irritation occurs.

Ingestion:

Get medical attention immediately. Do not induce vomiting, maintain rest, and timely medical care

Part V Fire Fighting Measures

Extinguishing media

Suitable extinguishing media: Use fire water spray, foam, dry chemical (dry powder) or carbon dioxide (CO2) to extinguish the fire.

water

Improper extinguishing media: None.

Fire

Fire instructions: Evacuate the area. Prevent the control of fire or diluted effluent from flowing into rivers, sewers or drinking water sources.

Firefighters should use standard protective equipment, use self-contained breathing apparatus in confined spaces, and expose to fire by spraying water.

The surface of the disaster cools down and protects the staff.

Fire hazard: Firefighters should consider using the protective equipment described in Section 8.

Hazardous combustion products: incomplete combustion products, carbon dioxide

Dangerous characteristics

No obvious hazard characteristics

Part VI Emergency measures for accidental leakage

Leakage treatment

Ground leaks: Do not touch or walk through leaked products. Avoid running into waterways, sewers, basements or narrow areas. .

Transfer to dry soil, sand or other non-inert materials and transfer to a container.

Water leakage: Precipitation and/or proper use of contaminants in open waters, if permitted by local agencies and environmental agencies

Powder. Consult the relevant experts for specific requirements for the disposal of all recycled materials and ensure compliance with local waste disposal regulations.

Part VII Operational Processing and Storage

Operational attention

Avoid prolonged or frequent contact with the skin. After treatment, wash your hands immediately before taking a break.

Loading and unloading temperature: room temperature

Transportation temperature: room temperature

Storage attention

Keep the container tight. Handle the container carefully. Store in a cool, well-ventilated place. Do not pressurize, cut, or

Heat or weld. Empty containers may contain product residues and should not be used until they have been professionally cleaned or reformed.

Storage temperature: normal temperature

Storage pressure: room temperature

Compatible materials and coatings: polyethylene; polypropylene; polyester, etc.

Incompatible materials and coatings: iron, aluminum, etc.

Part VIII Contact Control / Personal Protection

engineering control

Strictly closed, providing sufficient local exhaust. There are emergency showers such as eyewash.

personal protection

Respiratory protection: When the concentration in the air exceeds the standard, a filter-type gas mask (half mask) should be worn.

Hand protection: Use chemical resistant gloves (nitrile gloves).

Eye protection: If it is possible to contact, it is recommended to use safety glasses with side shields.

Skin and body protection: Use chemical/oil resistant antistatic overalls.

Other protections: Maintain good personal hygiene, such as washing hands after handling the product, and eating, drinking and/or

Wash your hands before smoking. Clean your work clothes and protective equipment regularly to remove contaminants. Discard contaminated clothing that cannot be washed

And shoes.

Part IX Physical and chemical properties

Physical state: liquid

Appearance: colorless to pale yellow

Smell: characteristic smell

Smell threshold: no data

Relative density (@ 20°C): 1.0358

Flash point : none

pH: 9~10

Melting point: <0°C

Boiling point : >100°C

Auto-ignition temperature: none

Decomposition temperature: no data

Relative vapor density (air = 1): not applicable

Saturated vapor pressure: no data available

Logogram of n-octanol/water partition coefficient: No data available

Solubility: soluble in water

Other physical properties: None

Part 10 Stability and reactivity

Stability: The product is stable under normal conditions.

Avoid contact conditions: Avoid excessive heat. High energy ignition source.

Avoid contact with substances: Strong oxidants, acids.

Hazardous decomposition products: In general, no decomposition occurs.

Hazardous Polymerization: No dangerous polymerization will occur.

Part XI Toxicological Information

Toxicological information

Acute toxicity	LD 50 (rat) / oral	LC50 rat) / oral	LD 50 (rabbit) / percutaneous	other
Acute toxicity	> 2000 mg/kg	>1000 mg/m3	> 2000 mg/kg	no
Subacute and chronic toxicity	no data
Irritating	no data
other	no data

Section 12 Ecological Information

Ecotoxicity	This product is considered harmless to aquatic organisms
Biodegradability	Rapid biodegradation
Non-biodegradable	Non-biodegradation is not obvious
Bioaccumulation	no data
Other harmful effects	no data

Section 13 Discarding Instructions

Disposal advice

This product is not suitable for disposal by deep burial and is not suitable for discharge into public sewers, drainage systems or natural rivers.

Empty drums should be recycled, recycled or disposed of by qualified or licensed agencies. In all cases, care must be taken to ensure compliance with national and local laws.

Disposal considerations

Refer to relevant government regulations.

Part Fourteen Transport Information

Package identification	Packing category
wrapping method	Refer to national and local regulations before disposal.
Transportation considerations	Lightly load and unload during handling to prevent damage to packaging and containers.
Ground transportation	Land transport is not regulated
Sea	Shipping is not regulated
air transport	Air transport is not regulated

Part 15 Regulatory Information

Corresponding provisions have been made for the safe use, production, storage, transportation, loading and unloading of chemical dangerous goods.

Regulations for the Safety Management of Chemical Dangerous Goods, implemented on December 1, 2011

General rules for the classification and hazard of chemicals GB 13690-2009 Implementation on May 1, 2010

SAFETY DATA SHEET Content and project sequence GB

16483-2008 Implemented on February 1, 2009

Regulations for the preparation of chemical safety labels GB 15258-2009 Implementation on May 1, 2010

Water Pollution Prevention Law / Waste Pollution Prevention and Control Act

Section 16 Additional Information

Note: This material applies only to the substance specified and may not apply to the mixing of the substance with other substances or during use.

This information is known to the product and is believed to be accurate and reliable. However, the accuracy, reliability and reliability of the information of the company

No commitment or guarantee of completeness. The user must be responsible for the suitability and completeness of the material for his or her own application.

Previous：Rosin Water-based cleaner T1002G TDS

Next：PCBA Cleaning Solution T1008P TDS